CAT Cat®16M3 Motor grader
Mass of complete machine (kg):
32411.0
Engine model:
Cat® C13 ACERT™ VHP
Rated power (KW):
216
Product Feature
Product Parameter
Engine | |
Basic power(1st gear)- Net power | 216.0 kW |
Engine model | Cat® C13 ACERT™ VHP |
Cylinder bore | 130.0 mm |
Stroke | 157.0 mm |
Speed at rated power | 2000 rpm |
VHP Range – Net worth | 216-259 kW(290-348 hp) |
VHP Range – Net worth(The metric system) | 216-259 kW(294-353 hp) |
Power derated altitude:Tier 2/Stage II/Japan 2001(Tier 2)Equivalent standard | 3954.0 m |
Power derated altitude:Tier 3/Stage IIIA/Japan 2006(Tier 3)Equivalent standard | 3711.0 m |
Power derated altitude:Tier 4/Stage IV/Japan 2014(Tier 4) | 3810.0 m |
Basic power(1st gear)– Net worth(The metric system) | 216.0 kW |
Torque reserve:Tier 2/Stage II/Japan 2001(Tier 2)Equivalent standard | 39% |
Torque reserve:Tier 3/Stage IIIA/Japan 2006(Tier 3)Equivalent standard | 39% |
Torque reserve:Tier 4/Stage IV/Japan 2014(Tier 4) | 43% |
Discharge (1) | America EPA Tier 4 Final/European Union Stage IV/Japan 2014(Tier 4 Final) |
Discharge (2) | Tier 3/Stage IIIA/Japan 2006(Tier 3)Equivalent emission standards – Depending on the particular country/Emission standards for the region |
Discharge (3) | Tier 2/Stage II/Japan 2001(Tier 2)Equivalent emission standards – Depending on the particular country/Emission standards for the region |
Maximum torque - ISO 9249:Tier 2/Stage II/Japan 2001(Tier 2)Equivalent emission standards | 1721.0 N·m |
Maximum torque - ISO 9249:Tier 3/Stage IIIA/Japan 2006(Tier 3)Equivalent emission standards | 1721.0 N·m |
Maximum torque - ISO 9249:Tier 4/Stage IV/Japan 2014(Tier 4) | 1771.0 N·m |
Standard - Environmental tolerance | 50.0 °C |
Standard – Fan speed:Lowest | 550 rpm |
Standard – Fan speed:Highest | 1450 rpm |
Optimized VHP The scope of – Net worth | 216-259 kW(290-348 hp) |
Displacement | 12.5 l |
Number of cylinders | 6 |
Power train | |
Forward/Reverse gear | 8 forward gears/6 reverse gears |
Gearbox | Direct drive,Power shift,Intermediate shaft |
Brake - Parking | Spring-type hydraulic release |
Brake - Repair | Oil start type,Oil bath pan |
Brake - Assist | Oil start type,Oil-immersed disc type |
Brake – Dynamic braking torque per wheel | 36701.0 N·m |
Hydraulic system | |
Loop type | Closed Center Electro-Hydraulic Load Sensing |
Pump type | Variable Piston |
Maximum system pressure | 24750.0 kPa |
Standby pressure | 5900.0 kPa |
Notice | *At 2150 rpm rpm Measured pump displacement at。 |
Pump displacement* | 280.0 l/min |
Operating specifications | |
Back a car - 1st gear | 3.6 km/h |
Back a car - Second gear | 6.6 km/h |
Back a car - Third gear | 9.7 km/h |
Back a car - Fourth gear | 15.0 km/h |
Back a car - Fifth gear | 28.0 km/h |
Back a car - 6th gear | 40.8 km/h |
Forward - 1st gear | 4.5 km/h |
Forward - Second gear | 6.1 km/h |
Forward - Third gear | 8.9 km/h |
Forward - Fourth gear | 12.3 km/h |
Forward - Fifth gear | 19.0 km/h |
Forward - 6th gear | 25.8 km/h |
Forward - Seventh gear | 35.5 km/h |
Forward - 8th gear | 51.7 km/h |
Top speed - Back a car | 40.8 km/h |
Top speed - Forward | 51.7 km/h |
Steering range - Left/Right | 47.5° |
Turning radius(Outside of front wheel) | 9.3 m |
Articulation angle – Left/Right | 20° |
Service fill | |
Fuel capacity | 496.0 l |
Cooling system | 70.0 l |
DEF Box | 16.0 l |
Hydraulic system - Totally | 146.0 l |
Hydraulic system - Fuel tank | 70.0 l |
Engine oil | 36.0 l |
Gearbox/Differential/Final drive | 98.5 l |
Two-wheel set housing(Each) | 129.0 l |
Front wheel spindle bearing housing | 0.9 l |
Circle drive box | 10.0 l |
Rack | |
Front frame structure - Width | 356.0 mm |
Front frame structure - Height | 460.0 mm |
Front frame structure – Thickness | 14.0 mm |
Front axle - Total swing on each side | 35° |
Front axle - Height to center | 670.0 mm |
Front axle – The wheel is tilted | Left 18°/Right 17° |
Rotary disk - Blade beam thickness | 50.0 mm |
Rotary disk- Diameter | 1822.0 mm |
Drawbar - Width | 76.0 mm |
Drawbar - Height | 203.0 mm |
Moldboard | |
Blade width | 4.9 m |
Arc radius | 413.0 mm |
Dento-laryngeal space | 126.0 mm |
Downforce – Basic GVW | 13945.0 kg |
Downforce – Max GVW | 19895.0 kg |
Stop Bit - Thickness | 19.0 mm |
Stop Bit - Width | 152.0 mm |
Thickness | 25.0 mm |
Blade pull* - Basic GVW | 18615.0 kg |
Blade pull* - Max GVW | 23985.0 kg |
Spade edge - Thickness | 25.0 mm |
Spade edge - Width | 203.0 mm |
Range of blade movement | |
Blade maximum roll angle | 65° |
Maximum lifting height above ground | 400.0 mm |
Maximum depth of cut | 470.0 mm |
Maximum blade length out of tire - Right side | 2311.0 mm |
Maximum blade length out of tire - Left side | 2311.0 mm |
Moldboard sidesway - Right side | 790.0 mm |
Moldboard sidesway- Left side | 740.0 mm |
The circle center is displaced - Right side | 560.0 mm |
The circle center is displaced - Left side | 690.0 mm |
Blade tip range - Forward | 40° |
Blade tip range - Backwards | 5° |
Ripper | |
Maximum depth of ripping | 452.0 mm |
Rack carrier spacing – Minimal | 445.0 mm |
Rack carrier spacing – Max | 500.0 mm |
Ripper rack | 7 |
Penetration | 13749.0 kg |
Digging force | 19822.0 kg |
Increase in machine length when the beam is raised | 1610.0 mm |
Weight | |
Operating weight - Typical configuration | 32411.0 kg |
Size(Approximation) | |
Ground clearance at rear axle | 396.0 mm |
Width - Outside of front tire | 3411.0 mm |
Width - Outside of rear tire | 3411.0 mm |
Width - Tire centerline | 2703.0 mm |
Height to exhaust pipe | 3557.0 mm |
Height to top of cylinder | 3088.0 mm |
Length - Front tire to rear of machine(Includes a traction hinge) | 10593.0 mm |
Length - Front axle to moldboard | 3066.0 mm |
Length - Front axle to tandem centre | 7365.0 mm |
Length - Axle spacing of double wheel set | 1841.0 mm |
Length - Counterweight to Ripper | 12051.0 mm |
Height - Center of front axle | 733.0 mm |
Height - The top of the cab | 3719.0 mm |
Standard | |
ROPS/FOPS | ISO 3471:2008/ISO 3449:2005 |
Brake | ISO 3450:2011 |
Noise | ISO 6394:2008/ISO 6395:2008/ISO 6396:2008 |
Turn | ISO 5010:2007 |
Double wheel set | |
Width | 4.9 m |
Height | 787.0 mm |
Side wall thickness - Inside | 22.0 mm |
Side wall thickness - External | 22.0 mm |
The double wheel set swings - Front up | 15° |
The double wheel set swings - Front down | 25° |
Drive chain pitch | 63.5 mm |
Axle spacing | 1841.0 mm |
Variable power | |
Gear:Forward - 1st gear | 216.0 kW |
Gear:Forward - Second gear | 216.0 kW |
Gear:Forward - Third gear | 222.0 kW |
Gear:Forward - Fourth gear | 227.0 kW |
Gear:Forward - Fifth gear | 232.0 kW |
Gear:Forward - 6th gear | 239.0 kW |
Gear:Forward - Seventh gear | 244.0 kW |
Gear:Forward - 8th gear | 259.0 kW |
Gear:Back off - 1st gear | 216.0 kW |
Gear:Back off - Second gear | 216.0 kW |
Gear:Back off – Gear 3 to 6 | 222.0 kW |
Weight TIER 4/STAGE IV/Japan 2014(TIER 4 FINAL) | |
Notice (1) | *If the machine is not equipped with Tier 4 Final Emission standard engine,150 shall be subtracted from the rear axle weight and the total weight kg(331 lb)。 |
Notice (2) | **Base operating weight is based on standard machine configuration,Including 23.5 R25 tires、Full tank、Operator and ROPS Cab。 |
Gross vehicle weight - Basic weight**:Total | 28816.0 kg |
Gross vehicle weight - Maximum measured weight:Front axle | 11850.0 kg |
Gross vehicle weight - Maximum measured weight:Rear axle | 26650.0 kg |
Gross vehicle weight – Typical configuration:Front axle | 8733.0 kg |
Gross vehicle weight – Typical configuration:Rear axle | 23678.0 kg |
Gross vehicle weight – Typical configuration:Total | 32411.0 kg |
Gross vehicle weight – Basic weight**:Front axle | 8134.0 kg |
Gross vehicle weight – Basic weight**:Rear axle | 20682.0 kg |
Gross vehicle weight – Maximum measured weight - Total | 38500.0 kg |
Optional tire configuration | |
Wheel set:19.5×25 MP (1) | Tire:23.5R25 Bridgestone VKT 2 Star |
Wheel set:19.5×25 MP (2) | Tire:23.5R25 Bridgestone VKT 1 Star |
Wheel set:19.5×25 MP (3) | Tire:23.5R25 Bridgestone VJT 1 Star |
Wheel set:19.5×25 MP (4) | Tire:23.5R25 Michelin XHA 2 Star |
Wheel set:19.5×25 MP (5) | Tire:23.5R25 Michelin XLDD 2 Star L5 |