Cat Large Wheel Dozers 834K Scoops
Product Feature
Efficiency
Cat C18 ACERT Engine
The Cat C18 ACERT engine is built and tested to meet your most demanding applications. Three C18 ACERT engine options are available in this machine: Tier 4 Final/Stage IV with aftertreatment, Tier 3 equivalent, or Tier 2 equivalent.
Fully integrated electronic engine controls works in concert with the entire machine to make your fuel go farther.
Use less fuel idling with Engine Idle Shutdown.
Maximized durability with Delayed Engine Shutdown.
Cat Planetary Powershift Transmission
Featuring all new Advanced Productivity Electronic Control Shifting (APECS) transmission controls provides greater momentum on grades and fuel savings by carrying that momentum through the shift points.
Impeller Clutch Torque Converter (ICTC)
Enable your operators to maximize efficiency by varying machine rimpull while putting more horsepower to hydraulics.
Reduced tire wear
Enables full throttle shifts for faster cycle times
Provides smooth approach to the dump target for less spillage and faster cycle times.
Cat Torque Converter with Lock-up Clutch
Eliminates TC losses while lowering system heat
Improves travel speeds
Reduces cycle times in load and carry operations
Improved Hydraulic Efficiency
New flow sharing implement and steering variable displacement load sensing piston pumps.
Hydraulic flow now on demand, for improved fuel efficiency.
Structures
Robust Structures
Your bottom line is improved by highly durable structures that achieve multiple life cycles and withstand the toughest conditions.
Full box-section rear frame resists torsional shock and twisting forces.
Heavy-duty steering cylinder mounts efficiently transmit steering loads into the frame.
Axle mounting has been optimized for increased structural integrity.
Lower hitch pin, frame plate, and bearing size have been increased for longer life.
Robust Structures Design
Push beams are through-width, not merely attached to side of frame.
In corner dozing, stresses are transferred and absorbed through a larger portion of the frame.
Power Train
Steering and Transmission Integrated Control System (STIC™)
Experience maximum responsiveness and control with STIC that combines directional selection, gear selection and steering into a single lever.
Simple side-to-side motion turns machine right or left, minimizing operator movements.
Easy to operate finger controlled gear selection.
Smoother, faster cycles and less operator fatigue through the use of low effort integrated controls.
Cat Planetary Powershift Transmission
Building your success begins with a best-in-class transmission designed specifically for mining applications.
Consistent, smooth shifting and efficiency through integrated electronic controls that utilize Advanced Productivity Electronic Control Strategy (APECS).
Long life and reliability through heat treat gear and metallurgy.
Four forward and three reverse speeds to match your application.
Cat C18 ACERT Engine
Durability and efficiency at the heart of your 834K comes from the Cat C18 ACERT Engine. Optimum performance is built in through the use of a 6 cylinder, four-stroke design.
Optimized performance and quick engine response with an electronic control module.
Reliable efficiency with complete control over injection timing, duration and pressure with Mechanically Actuated Electronic Unit Injection (MEUI™).
Extended engine life and improved fuel efficiency with reduced rated speed.
Option of: Tier 4 Final/Stage IV emissions standards, Tier 3 equivalent, or Tier 2 equivalent.
Impeller Clutch Torque Converter (ICTC) and Rimpull Control System (RCS)
Lower your operating costs utilizing advanced ICTC and RCS for modulated rimpull.
Reduce tire slippage and wear by modulating rimpull from 100 to 25 percent while depressing left pedal. After 25 percent rimpull is achieved the left pedal applies the brake.
Reduce the potential for wheel slippage without reducing hydraulic efficiency with RCS.
Improve fuel efficiency in certain applications with our lock-up clutch torque converter providing direct drive.
Operator Station
Your operators can work more efficiently and stay comfortable with our customer-inspired cab features.
Entry and Exit
Enter and exit the cab easily and safely with these newly designed, ergonomic features.
Fold up STIC steer/armrest.
Reduced angles on access stairways.
Standard stairway lighting.
Cat Comfort Series III Seat
Enhance comfort and reduce operator fatigue with Cat Comfort Series III seat.
Mid back design and extra thick, contoured cushions.
Air suspension system.
Easy-to-reach seat levers and controls for six way adjustments.
Seat-mounted implement pod and STIC steer that moves with the seat.
76 mm (3 in) wide retractable seat belt.
Control Panel
Ergonomic placement of switches and Information display keep your operators comfortable all day every day.
Large backlit membrane switches feature LED activation indicators.
Switches feature ISO symbols for quick function identification.
Two position rocker switch activates the electro hydraulic park brake.
Environment
Your operator's productivity is enhanced with our clean, comfortable cab environment.
Experience reduced vibrations from isolation cab mounts and seat air suspension.
Maintain desired cab temperature with automatic temperature controls.
Pressurized cab with filtered air.
Sound level reduced to a quiet 71 dB(A) when equipped with the sound suppression package.
Convenient floor storage tray/lunch box.
Technology Solutions
The 834K electronic systems have been completely integrated to function as one machine. This integration creates a smart machine and more informed operator, maximizing the productivity of both.
Cat Product Link™
Cat Product Link allows remote monitoring of equipment to improve overall fleet management effectiveness. Events and diagnostic codes, as well as hours, fuel, idle time and other information are transmitted to a secure web based application, VisionLink™. VisionLink includes powerful tools to convey information to users and dealers, including mapping, working and idle time, fuel level and more.
VIMS™ 3G
We have worked hard to help our customers and operators perform at their best through our Vital Information Management System (VIMS 3G).
Easy-to-view graphical information display features a large touch screen interface.
Intuitive operation and easy navigation with our enhanced user interface.
Decrease service time by keeping operators informed about machine system malfunction or operation.
Cat MineStar System
Cat MineStar System is the industry's broadest suite of integrated mine operations and mobile equipment management technologies, configurable to suit your operation's needs. Its capability sets – Fleet, Terrain, Detect, Health and Command – contain a range of technologies that let you manage everything from fleet assignment and condition monitoring to remote and autonomous control. The 834K can take advantage of many of these advanced technologies, some of which are standard out of the factory.
Fleet
Fleet provides comprehensive, real-time machine tracking, assignment and productivity management, giving you a comprehensive overview of all operations from anywhere in the world.
Terrain for Loading
Terrain with your 834K enables high-precision management of loading operations through the use of guidance technology. It increases 834K productivity and provides you real-time feedback for improved efficiency.
Detect
Detect helps increase operator awareness, enhancing safety at your operation. It includes a range of capabilities designed to assist the operator with areas of limited visibility around fixed and mobile equipment.
Health
Health delivers critical event-based machine condition and operating data for your entire fleet. It includes comprehensive equipment health and asset monitoring capabilities, with a wide range of diagnostic, analytic and reporting tools.
Safety
We are constantly introducing features on our machines in an effort to enhance safety for the operator.
Machine Access
Left and right hand stairs with 45 degree angle enhance safety for operators getting on and off the 834K.
Continuous walkway with non-skid surfaces are designed into the service areas.
Maintain three points of contact at all times through ground level or platform accessible service areas.
Visibility
Optional heated mirrors ensure enhanced visibility for safe operation.
Standard Cat Vision or optional Cat Detect with radar increase operator awareness around the machine.
LED lights provide excellent workspace visibility.
Optional cab mounted LED warning beacons.
Operator Environment
Reduced vibrations to the operator with isolated cab mounts and seat mounted implement and steering controls.
Low interior sound levels.
Pressurized cab with filtered air.
Standard 76 mm (3 in) seat belts on the operator seat.
Sustainability
Sustainability is designed and built into our 834K's features.
Engine Idle Shutdown and Auto Idle Kickdown can help you save fuel by avoiding unnecessary idling.
Reduce waste generation with our maintenance free batteries.
The 834K is built for multiple lives. To assist with maximizing machine life, Caterpillar provides a number of sustainable options such as our Reman and Certified Rebuild programs. In these programs, reused or remanufactured components can deliver cost savings of 40 to 70 percent, which lowers operating cost.
Caterpillar offers retrofit packages to bring new features to older machines, maximizing your resource. And, when you go through the Cat Certified Rebuild program, these retrofit kits are part of the rebuild process.
Productivity
Purpose Built Front Linkage
Cat wood chip and coal scoops have the unique capability of maximizing your production by both dozing and carrying a load with each pass. A purpose built hydraulic system is optimized for use with this work tool to maximize machine productivity and efficiency. Dual lift cylinders provide hydraulic lift capacity matched to the demands of the application.
Oscillating Rear Axle
The fixed front axle and oscillating rear axle ensures four-wheel ground contact for optimum traction and stability. The front axle is rigidly mounted to the front loader frame, while the rear axle is allowed to oscillate. This configuration allows the operator's view of the scoop to remain constant as the rear axle oscillates enabling the operator to maintain a smooth and properly graded work area in any underfoot conditions.
Operating Costs
The 834K has several features to achieve greater fuel efficiency:
Positive Flow Control Hydraulics – Provides only the hydraulic flow required by the implement and steering systems for improved fuel efficiency and greater rimpull.
ACERT Engine – Advanced engine controls maximizes power and efficiency.
Engine Idle Shutdown – Automatic engine and electrical system shutdown conserves fuel.
Lock-up Torque Converter – Transfers more power to the ground and optimizes fuel efficiency in all applications.
Advanced Productivity Electronic Control Strategy (APECS) – All new APECS transmission controls provides greater momentum on grades and fuel savings by carrying that momentum through the shift points.
Machine configuration, operator technique, and job site layout can impact fuel consumption.
Machine Configuration – Select the correct work tool and tire type based on machine application. Ensure proper inflation pressures.
Idle – Set the parking brake to engage Engine Idle Management System.
Serviceability
We can help you succeed by ensuring your 834K has design features to reduce your downtime.
Safe and convenient service with ground level or platform access and grouped service points.
Swing-out doors on both sides of the engine compartment provide easy access to important daily service checks.
Ecology drains for ease of service and prevention of spilling potential environmental contaminants.
Reduce downtime with VIMS system notifications so your operators and technicians can resolve any problems before failure.
Ground level access to transmission control valves.
Customer Support
Legendary Cat Dealer Support
A valued partner, your Cat dealer is available whenever you need them.
Preventive maintenance programs and guaranteed maintenance contracts.
Best-in-class parts availability.
Improve your efficiency with operator training.
Genuine Cat Remanufactured parts.
Product Parameter
Overview
Cat Wheel Dozers are designed with durability built in, ensuring maximum availability through multiple life cycles. With optimized performance and simplified serviceability, our machines allow you to support your job site efficiently and safely while lowering owning and operating costs. Introduced in the mid-1960's, the 834 has been the industry leader for almost 50 years. Focused on helping our customers succeed, we have continued to build upon each new series. The 834K continues our legacy of reliability, performance, safety, operator comfort, serviceability, and efficiency.
Engine
Units:
Engine Model | Cat® C18 ACERT™ Cat® C18 ACERT™ | More |
Net Power | 496.0 HP 370.0 kW | More |
Bore | 5.7 in 145.0 mm | More |
Stroke | 7.2 in 183.0 mm | More |
Displacement | 1105.0 in³ 18.1 l | More |
Emissions | U.S. EPA Tier 4 Final/EU Stage IV, Tier 3 Equivalent, or Tier 2 Equivalent U.S. EPA Tier 4 Final/EU Stage IV, Tier 3 Equivalent, or Tier 2 Equivalent | More |
Gross - SAE J1349 | 562.0 HP 419.0 kW | More |
Net - SAE J1349 | 496.0 HP 370.0 kW | More |
Peak Power Speed | 1,500 rpm 1,500 rpm | More |
Peak Torque - 1,300 rpm | 2092.0 ft·lbf 2836.0 N·m | More |
Rated Speed | 1,900 rpm 1,900 rpm | More |
Torque Rise | 52% 52% | More |
Transmission
Direct Drive - Forward 1 | Lock-up disabled Lock-up disabled | More |
Direct Drive - Forward 2 | 7.7 mile/h 12.4 km/h | More |
Direct Drive - Forward 3 | 13.7 mile/h 22.1 km/h | More |
Direct Drive - Forward 4 | 23.9 mile/h 38.5 km/h | More |
Direct Drive - Reverse 1 | 4.5 mile/h 7.2 km/h | More |
Direct Drive - Reverse 2 | 8.1 mile/h 13.0 km/h | More |
Direct Drive - Reverse 3 | 14.3 mile/h 23.0 km/h | More |
Forward - 1 | 4.2 mile/h 6.8 km/h | More |
Forward - 2 | 7.2 mile/h 11.6 km/h | More |
Forward - 3 | 12.6 mile/h 20.3 km/h | More |
Forward - 4 | 22.0 mile/h 35.4 km/h | More |
Reverse - 1 | 4.2 mile/h 6.8 km/h | More |
Reverse - 2 | 7.6 mile/h 12.2 km/h | More |
Reverse - 3 | 13.3 mile/h 21.4 km/h | More |
Transmission Type | Cat planetary power shift Cat planetary power shift | More |
Note | Travel speeds based on 35/65-R33 tire. Travel speeds based on 35/65-R33 tire. | More |
Brakes
Brakes | ISO 3450:2011 ISO 3450:2011 | More |
Axles
Front | Fixed Fixed | More |
Rear | Trunnion Trunnion | More |
Oscillation Angle | ±13° ±13° | More |
Weights
Operating Weight | 112838.0 lb 51290.0 kg | More |
Service Refill Capacities
Cooling System | 31.7 gal (US) 120.0 l | More |
Crankcase | 15.9 gal (US) 60.0 l | More |
Transmission | 31.7 gal (US) 120.0 l | More |
Diesel Exhaust Fluid Tank* | 8.7 gal (US) 33.0 l | More |
Differential - Final Drives - Front | 49.1 gal (US) 186.0 l | More |
Differential - Final Drives - Rear | 49.1 gal (US) 186.0 l | More |
Fuel Tank | 209.5 gal (US) 793.0 l | More |
Hydraulic System - Tank Only | 37.0 gal (US) 140.0 l | More |
Hydraulic System Factory Fill | 63.4 gal (US) 240.0 l | More |
Note (1) | All non-road Tier 4 Final/Stage IV Technology diesel engines are required to use: – Ultra Low Sulfur Diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfur or less. Biodiesel blends up to B20 are acceptable when blended with 15 ppm (mg/kg) sulfur or less ULSD and when the biodiesel feedstock meets ASTM D7467 specifications. – Cat DEO-ULS™ or oils that meet the Cat ECF-3, API CJ-4, and ACEA E9 specifications are required. All non-road Tier 4 Final/Stage IV Technology diesel engines are required to use: – Ultra Low Sulfur Diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfur or less. Biodiesel blends up to B20 are acceptable when blended with 15 ppm (mg/kg) sulfur or less ULSD and when the biodiesel feedstock meets ASTM D7467 specifications. – Cat DEO-ULS™ or oils that meet the Cat ECF-3, API CJ-4, and ACEA E9 specifications are required. | More |
Note (2) | *Only applicable to Tier 4 Final/Stage IV equipped machines. *Only applicable to Tier 4 Final/Stage IV equipped machines. | More |
Operating Specifications
Chip Scoop Operating Weight | 112838.0 lb 51290.0 kg | More |
Coal Scoop Operating Weight | 112428.0 lb 51103.0 kg | More |
Sound Performance - Tier 4 Final/Stage IV - Standard
Machine Sound Level (ISO 6395) | 111.0 dB(A) 111.0 dB(A) | More |
Operator Sound Level (ISO 6396) | 73.0 dB(A) 73.0 dB(A) | More |
Note (1) | The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. | More |
Note (2) | Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. | More |
Note (3) | The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. | More |
Sound Performance - Tier 4 Final/Stage IV: Suppression
Machine Sound Level (ISO 6395) | 109.0 dB(A) 109.0 dB(A) | More |
Operator Sound Level (ISO 6396) | 72.0 dB(A) 72.0 dB(A) | More |
Note (1) | The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. | More |
Note (2) | Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. | More |
Note (3) | The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. | More |
Dimensions (Approximate)
Centerline of Front Axle to Hitch | 7.5 ft 2275.0 mm | More |
Centerline of Rear Axle to Edge of Bumper | 10.5 ft 3187.0 mm | More |
Ground Clearance | 1.7 ft 531.0 mm | More |
Ground to Center of Front Axle | 3.2 ft 978.0 mm | More |
Height - Top of Air Cleaner | 12.8 ft 3895.0 mm | More |
Height - Top of Cab | 13.7 ft 4184.0 mm | More |
Height - Top of Exhaust Stack | 14.8 ft 4498.0 mm | More |
Height - Top of Hood | 10.9 ft 3334.0 mm | More |
Length - Front of Tire | 28.4 ft 8715.0 mm | More |
Length - With Chip Scoop on Ground | 39.3 ft 11974.0 mm | More |
Length - With Coal Scoop on Ground | 39.3 ft 11971.0 mm | More |
Wheel Base | 14.9 ft 4550.0 mm | More |
Dump Angle at Full Lift Height | 64 deg 64 deg | More |
Height - Edge of Dumped Scoop | 5.0 ft 1520.0 mm | More |
Height - Edge of Retracted Scoop | 7.4 ft 2250.0 mm | More |
Scoops
Coal Scoop Carry Capacity | 30.0 yd³ 22.9 m³ | More |
Chip Scoop Carry Capacity | 35.0 yd³ 26.8 m³ | More |
Chip Scoop Doze Capacity | 70.0 yd³ 53.5 m³ | More |
Coal Scoop Doze Capacity | 60.0 yd³ 45.9 m³ | More |
Components | Both scoops come with dual lift cylinders for increased lift capacity. Integrated stabilizer system makes sure that the scoop stays stable and centralized on the machine. Scoop tilt function is standard and provides ±15 degrees of tilt to maintain grade conditions and keep your operation safe. Both scoops come with dual lift cylinders for increased lift capacity. Integrated stabilizer system makes sure that the scoop stays stable and centralized on the machine. Scoop tilt function is standard and provides ±15 degrees of tilt to maintain grade conditions and keep your operation safe. | More |
Type | Large capacity scoops for both wood chip and coal applications. A mesh screen integrated into the back of the scoop maintains visibility to the cutting edge. The chip scoop version has extra screens at the top due to higher capacity. Large capacity scoops for both wood chip and coal applications. A mesh screen integrated into the back of the scoop maintains visibility to the cutting edge. The chip scoop version has extra screens at the top due to higher capacity. | More |
Hydraulic System - Lift/Dump/Tilt
Cylinders, Double Acting - Left and Right Dump, Bore and Stroke | 127 mm × 838 mm (5.0 in × 33.0 in) 127 mm × 838 mm (5.0 in × 33.0 in) | More |
Cylinders, Double Acting - Lift, Bore and Stroke | 170.0 mm × 1107 mm (6.7 in × 43.6 in) 170.0 mm × 1107 mm (6.7 in × 43.6 in) | More |
Lift/Tilt System | Variable displacement piston Variable displacement piston | More |
Lift/Tilt System - Circuit | Pilot operated LS valve with EH Pilot operated LS valve with EH | More |
Maximum Flow at 1,900 rpm | 153.0 gal/min 582.0 l/min | More |
Pilot Maximum Flow | 13.7 gal/min 52.0 l/min | More |
Pilot Relief Valve Setting | 580.0 psi 4000.0 kPa | More |
Pilot System | Variable displacement piston Variable displacement piston | More |
Relief Valve Setting - Lift/Tilt | 4206.0 psi 29000.0 kPa | More |
Cylinders, Double Acting - Tilt, Bore and Stroke | 152.4 mm × 953 mm (6.0 in × 37.5 in) 152.4 mm × 953 mm (6.0 in × 37.5 in) | More |
Hydraulic System - Steering
Maximum Flow | 65.8 gal/min 250.0 l/min | More |
Relief Valve Setting - Steering | 3495.0 psi 24100.0 kPa | More |
Steering Cycle Times - High Idle | 3.1 s 3.1 s | More |
Steering Cycle Times - Low Idle | 5.7 s 5.7 s | More |
Steering System - Circuit | Pilot, load sensing Pilot, load sensing | More |
Steering System - Pump | Piston, variable displacement Piston, variable displacement | More |
Total Steering Angle | 86° 86° | More |
Air Conditioning System
Air Conditioning | The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes. The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes. | More |
Sound Performance - Tier 2 Equivalent/Stage II: Standard
Machine Sound Level (ISO 6395) | 112.0 dB(A) 112.0 dB(A) | More |
Note (1) | The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. | More |
Note (2) | Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. | More |
Note (3) | The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. | More |
Operator Sound Level ( ISO 6396) | 81.0 dB(A) 81.0 dB(A) | More |
Sound Performance - Tier 2 Equivalent/Stage II: Suppression
Machine Sound Level (ISO 6395) | 109.0 dB(A) 109.0 dB(A) | More |
Note (1) | The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. | More |
Note (2) | Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. | More |
Note (3) | The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. – The measurement was conducted at 70 percent of the maximum engine cooling fan speed. | More |
Operator Sound Level (ISO 6396) | 81.0 dB(A) |