Cat Wheel Asphalt Pavers AP1000F

Easy Operation

F-Series pavers allow Cat Grade Control to be operated from any of the two tractor or two screed consoles. Split screen mode can be setup to monitor each side of the screed allowing a single person to monitor operation.

Precise Control

More accurate control, maximizes mix utilization, saves money. True averaging with sonic sensors that utilize 5 transducers, 2 readings are discarded and 3 averaged. A 10-point Auto-Calibration procedure eliminates over/under adjustment from a single calibration point. Cross-coupling, slope and elevation are maintained with height adjustments. The true 9 m (30 ft) sonic averaging beam modifies tow point movement by 1/3 of total grade deviation.

Highly Reliable

Water-resistant displays, factory installed components, and consistent routing deliver performance. Sealed components withstand heat, moisture, and vibration, and the built-in temperature sensors provide better reliability than bail-type sensors.

Power Turning System

A postion sensor located in the left steering cylinder helps maintain consistent travel speeds when making turns by adjusting the drive speed of the propel motors according to the steering angle of the front wheels. This unique system leads to better mat quality and less wear on the drive system.

Four-Wheel Drive

Provides power to the front bogie wheels for additional traction. A dedicated pump delivers a 50% increase in torque over previous models.

All-Wheel Drive

Provides power to the front and rear bogie wheels. It delivers a 200 % increase in pull force over the previous models.

Single Touch Operation

Single touch features for the auto-fill feeder system, feeder system activation, and hopper control, allow operators to concentrate on truck exchanges and other duties for improved efficiency.

Simple Technology

Technology helps operators perform. Intuitive symbols and large graphics simplify operation., while the interactive LCD display with touchscreen access to generator activation, screed temperature control, and mix height adjustment, increase efficiency.

Screed Heat Technology

Exclusive zone monitoring allows heating to continue in the event of a temperature sensor failure. The system also monitors heating elements for failure conditions, eliminating unnecessary replacement.

Easy Adjustment

Feeder system ratio adjustment capability from the screed provides versatility. Standard hydraulic adjustment for extender height, slope, and crown, allows for on-the-go adjustment at standard and maximum paving widths.

Two-Speed Proportional Extender Control

Exclusive two-speed proportional extender control provides slower speed for precise control around obstacles and quick reaction when extending paving widths.

Better Efficiency

The heating elements slide out for easy replacement, no need to remove the screed plates. Machined screed frames simplify plate replacement and leveling.

Tamper Bar Screed Option

Tamper bar equipped screeds increase density as it tucks material under the screed plates. Three stroke settings of 2, 4, and 7 mm combine with a variable tamper speed of 0 to 1800 rpm to provide versatility.

Wide-Width Paving Packages

Exclusive power controls simplify adjustment across the entire 10 m (33 ft) paving width for better mat texture and quality. An innovative hooking system utilizes extender slope to attach wide-width paving packages, eliminating the need for additional lifting devices.

Quiet Heating

Quiet heat mode operates at an engine speed of 1300 rpm and provides heating in under 15 minutes.

Quick Heating

Quick heating mode provides a heat-up time in under 35 minutes when equipped with the 10 m (33 ft) wide-width paving package.

Temperature Ranges

Three preset heating options provide a wide range of temperatures for various mix designs; Low is 110 degrees C or 230 degrees F, medium is 130 degrees C or 266 degrees F, high is 160 degrees C or 320 degrees F.

Auto-Fill Feeder System

The auto-fill system simplifies starts by alternating the conveyors and augers until the mix height reaches the sensor point.

Single Touch Feeder System

The single touch feeder system automatically activates the entire feeder system with a single button for better efficiency.

One Touch Hopper Control

The hopper wings and hydraulic apron can be folded with a single touch and release. The system can be tailored to activate left or right wings, or the front hydraulic apron independently or together.

Cleanout and Warm-Up Mode

This feature activates the augers, conveyors, and tamper-bar (if equipped) at a reduced speed, allowing the application of release agents to prevent material build-up.

Mix Height Adjustment

Mix height adjustment in front of the screed can be modified from the tractor LCD display for increased versatility when needed.

Hydraulic Mainframe Extensions

The optional 457 mm (18") hydraulic mainframe extensions attach to the auger assembly and provide smooth material flow out to the extenders. They retract with the screed extensions when reducing paving widths.

Multiple Feed Sensor Options

The feeder system can be tailored to automatically operate with 0, 2, or 4 feed sensors. When paving with 0 sensors due to a failure, simply set the feeder system to automatic and adjust the mix height setting, no need to cycle the manual switch as previous models required.

Easier Service

Hardware-free bed plates simplify replacement and bottom side mounting hardware for the chain guards eliminates bolt wear and material build-up for easier replacement.

Better Visibility, Exceptional Comfort

The dual independent operating stations can extend beyond the frame for good all-around visibility. The low profile, front-mounted cooling system improves forward viewing and the redesigned auger assembly optimizes visibility to material height in front of the screed. The heated seat option, multiple seat adjustments, and tilting consoles conform to the operator to provide day-long comfort. Also, the top-mounted cooling system directs fumes, hot air, and fan noise away from the crew for a cooler and quieter working environment.

Fumes Management System

The exclusive ventilation system draws fumes from the conveyor tunnel as well as the auger chamber and redirects them away from the operator for a more comfortable working environment.

Cat C7.1 Engine

The C7.1 engine provides 168 kW (225 hp) at 2200 rpm and meets U.S. EPA Tier 4 Final and EU Stage IV emmision standards.

Eco-mode

Eco-mode utilizes an engine speed of 1650 rpm and reduces fuel burn by up to 5% over Cat E-series pavers while also lowering sound levels even more.

Automatic Engine Speed Control

When automatic engine speed control is activated, the engine speed is reduced to an idle speed of 1000 rpm when the propel lever is moved to neutral, or to 1300 rpm when screed heat is active.

Advanced Eco-mode

Eco-mode and automatic engine speed control when activated together modify the engine rpm based on load factors. When activated the engine will operate at 1650 rpm when paving. If the upper power threshold is exceeded, the engine speed will increase to 2200 rpm and remain there until the demand drops below the threshold and remains there for 30 seconds, ensuring reliable performance.