Product Feature
Power train - Engine
Engine
Cat 3516B Large displacement EUI Quad Turbocharged and Aftercooled Diesel Engine，Provides an increase of 5% in the most demanding mining operations% Higher power and stronger power management ability，In order to achieve the best transport performance。
Design
3516B 16-cylinder four-stroke design，Use of long useful power strokes，Its fuel burns more thoroughly.，More efficient。
Conform EPA Standard
Cat 3516B Large displacement engines comply with the US Environmental Protection Agency Tier I Emission standards。
Altitude compensation
At an altitude of 2750 m（9000'）The following can achieve the highest work efficiency。
High altitude arrangement（HAA）
Optional Cat 3516B The family of quad turbocharged and aftercooled short stroke diesel engines can operate at altitudes greater than 2750 m（9000 '）Provides full power without derating when。
High torque reserve
It's accelerating、Steep slopes and rough ground conditions，23% The torque net reserve rate provides unrivaled traction。 Efficient coordination of torque reserve with transmission shift point，Can greatly improve efficiency，Shorten the cycle time。
And the service life is prolonged
Large displacement、Low speed rating and stable power rating，This means more road transport time and shorter repair times。
One-piece piston design
New one-piece forged steel pistons with integral forged steel skirts are stronger and more durable，Can withstand the high temperature and high pressure of the engine，And that combustion efficiency can be improve.，Improve fuel efficiency and reduce emissions。 Corrosion-resistant stainless steel top ring lowers the ring、Wear of grooves and bushings，The reliability is greatly enhanced and the service life is prolonged。
Electronic unit injection（EUI）
The electronically controlled unit injection system can judge the working condition.、Adjust the oil supply，For optimum fuel efficiency。 High-pressure fuel system provides better response time and higher combustion efficiency，Less emissions and less smoke。
Electronic Control Module（ECM（Electronic Control Module，Electronic Control Module））
ECM Advanced engine management software，Monitoring with self-diagnostic electronic sensor、Control and protect the engine。 Computerized system senses working conditions and required power at all times，And adjust the engine，For maximum performance and efficiency.。
Separate circuit aftercooler
The aftercooler circuit can be operated at a lower temperature than the jacket water temperature.，Thus making the intake air denser.，Burn more fully。
Cooling system
New modular high-density cooling system with larger fan is hydraulically driven，Better cooling effect、Lower fuel consumption and noise level。
Refueling system（ORS）
Optional oiling system extends engine oil change intervals from 500 hours to 4000 hours or more，Improved machine utilization、And that cost is reduce。
Engine protection
Air intake and exhaust system
Cylinder block
Crankshaft and bearings
Bushing
Turbocharger
Damping
Fuel tank
Power train - Sales configuration
Sales configuration
793D There are 4 plain configurations and 1 high altitude configuration to choose from。 All configurations offer higher ramp speeds and are equipped with key components that match the performance requirements of the transport application and operating conditions。
Standard arrangement
The standard arrangement is designed for exceptional all-round performance。 These three factors give the truck wheels a power ratio of 793C Increased by 9%，These include：Increased by 5% Engine power；Common rail hydraulic system，Improved driveline efficiency；Demand Operated Hydraulically Driven Fan，Run only when needed，Reduced parasitic load。 Higher power to the wheels reduces cycle times，Reduce cost per ton。
Durable wheel assembly
This arrangement is designed for uphill haulage applications，Designed to extend the service life and transport performance of the wheels on long uphill transport。 Endurance wheel assemblies feature larger, more durable components，Includes a larger mandrel、Wider bearing spacing、Larger brake area and long-life friction disc material，Thereby prolonging the service life and the overhaul period of the brake.。
Ultra high speed configuration
Ultra high speed configuration designed for long distance on grade transportation，Maximum vehicle speed increased by 10% through the use of a new powertrain input gear assembly%，Up to 60 km/h（37 mph）。 This configuration also includes a durable wheel assembly。
Super deceleration configuration
This configuration is designed for long-distance downhill load transport，Special downshifts are usually provided，Increases downhill deceleration by 35%。 The super-strong deceleration configuration is achieved by adding a stronger wheel assembly、Bigger brake、Long-lasting friction material and additional cooling capacity。
High altitude arrangement
Designed for high altitude applications，3516B Short stroke engines can be used at high altitudes. - 2750 to 1600 m（9000 to 12000'）Provides enhanced power management when。 This configuration also includes a very strong deceleration configuration。
Power train - Gearbox
Mechanical power train
Cat Mechanical power trains and power shift transmissions are available on steep grades、Unparalleled operating efficiency and control in rough terrain conditions and on haul roads with high rolling resistance。
1）Gearbox
Cat Six-Speed Planetary Power Shift Transmission and Direct Injection 3516B HD Full cooperation of diesel engine，Stable power over a wide range of operating speeds。
• Robust design
To fit 3516B HD More horsepower from the engine，The proven planetary powershift transmission is built to be very solid，Long service life between overhaul。
• And that service life is long
Specially developed tanks and circuits，Provide colder、Cleaner oil，To improve performance and extend component life。
• Transmission Chassis Control（TCC）
TCC Electronic conversion of engine speed data，Shift at the preset point，So as to achieve the best performance、Efficiency and clutch life。
2）Lock-up torque converter
It blends the maximum rimpull and smooth shifting of torque converter drive with the efficiency and performance of direct drive。 The lock-up torque converter is approximately 8 at speed km/h（5 mph）Engage when，More power to the wheel。
• Lock-up clutch
Fast clutching，Reduce the torque load on the power train，Makes shifting smoother，Longer life，Driving is more comfortable。
• Smooth shifting
Separately adjusted clutch for smooth engagement，Thereby optimizing performance，Longer clutch life。
3）Final drive
Cat The final drives operate as a system with the planetary power shift transmission.，Transmitting maximum power to the ground。 To withstand high torque and shock loads，Double reduction final drives provide multiple torque，Further reduce driveline stress。
• Rear axle filter
New filtration system provides cooler、Cleaner oil，O as to prolong the service life of the component。
• Steering system
The design of the hydraulic steering control system makes the steering exceptionally smooth.，Precise control。 Separate circuit to avoid cross contamination，And the service life is prolonged。
• Secondary steering
The secondary steering system uses a pressure accumulator，In the event of engine failure，Up to 3 90-degree turns。
• Wheels and rims
Cast rear wheel and Cat Center-mounted rim，Secure with studs and nut，The maintenance workload is small，Durable。
Engine/Powertrain integration
Cat Data link
A compute system that integrates machine through electronic technology.，This optimizes the overall performance of the power train、And reliability is improve、Extend component life and reduce operating costs。
Electronic Technician（Cat ET）
Use Cat Electronic Technician Service Tool，Through Cat Data link，Stored diagnostic data can be easily read by the service technician，Simplify fault diagnosis and improve machine availability。
Integrated brake control（IBC）
IBC Integrate hydraulic automatic retarder control and traction control into one system，Maximize performance and efficiency。
Hydraulic Power Management System
This system is also referred to as a common rail hydraulic system，Reduce parasitics in power management system components and the new hydraulic fan drive system（Useless、Waste）Loss。 Two new variable displacement piston pumps drive the entire system。 These two oil pumps mainly supply oil to the steering and cooling functions.，Not related to the brake and lift circuit。 One pump is dedicated to the new demand hydraulic fan drive system。 Another pump provides output to the new constant pressure valve，And steer for that propeller.、Brake cooling、Rear axle filter（RAX）And optional RAX The cooling system provides hydraulic pressure and flow。 The system continues to improve the steering system as a priority.，While improving brake cooling and RAX Functional power management solution。 By reducing losses，The system is able to deliver more horsepower to the ground。
Caterpillar Braking system
Integrated brake system
Cat Reliable performance of oil-cooled brake system，On a very severe transport road，Can be controlled freely。 The integrated system will apply the service brake、Auxiliary braking、Parking brake and retarding functions in one powerful system，Braking efficiency is optimized。
Cat Data link
All control modes pass Cat Data link communication and working together，As an integrated system，Significantly improve productivity，And prolong that service life of the component。
Oil-cooled multi-disc brake
Caterpillar Four-wheel, forced oil-cooled, multiple disc service brakes with water/The oil heat exchanger is continuously cooled，Provides excellent non-fading braking and retarding performance。
Long life disc brake
Extended life friction material provides up to twice the wear life of standard brake，And twice as resistant to glazing.，This provides continuous braking force and less noise。
Brake design
Cat Oil-cooled disc brake design with large discs，Reliable performance，No adjustment is required。 The brakes are totally enclosed and hermetically sealed，To avoid contamination and reduce maintenance。
And that service life is long
An oil film protects the brake discs from direct contact。 The design uses shear oil molecules and heat transfer to absorb the braking force，So that that service life of the brake is prolon。
Piston
Caterpillar The two-piece piston design puts the service brakes in place.、Auxiliary braking、Parking brake and retarding functions are integrated into one system。 The service braking function and the retarding function are hydraulically activated by the primary piston。 The auxiliary piston is spring-loaded，Is held in the disengaged position by hydraulic pressure。 Once the pressure of the hydraulic system drops below the specified pressure，The brake is automatically applied by the secondary piston, which is moved by a spring。
Parking brake
Pushed by a spring、Hydraulically released, oil-cooled parking brakes are applied to all four wheel，Up to 15% Excellent parking braking capability on a variety of slopes。
Hydraulic automatic retarder control（HARC）
The hydraulically activated automatic retarder control system electronically controls hill deceleration，To maintain optimum engine speed and oil cooling。 Manual retarder or brake pedal can also be used to assist braking。 The operator applies the brake or the accelerator control to disable HARC。
HARC Production advantage
Faster
HARC Allows the operator to maintain optimum engine speed，Accelerate downhill travel speed，And that production efficiency is improve。
Excellent control
Automatic adjustment by brake，Smooth ride and good control even in slippery conditions，This allows the operator to concentrate on driving。
The operation is simple
HARC Improves the simplicity of operation，Increases operator confidence，Reduce fatigue。
Engine overspeed protection
When the engine speed exceeds the factory preset level，To avoid potential damage from engine overspeed，Regardless of operator action，HARC Will start automatically。
Slow down at the four corners
Four corner deceleration functions forward respectively/The rear wheels provide 60%/40% Braking force，Available in wet and slippery ground conditions，Provides excellent braking control。 Brake torque for front and rear balance，Provides excellent braking performance，Pecially during deceleration braking，Maximum protection against wheel lock。
Traction control system（TCS）
Electronically monitor and control rear wheel slip to increase traction，Improve truck performance in tough terrain condition。 If the slip rate exceeds the set limit，The oil-cooled disc brake will engage and slow down that wheel spin。 The torque is then automatically transferred to the wheel with the better traction。
Differential operation
Normal differential operation in slippery condition，Provides excellent maneuvering control。
Integrated brake control（IBC）
Control the hydraulic automatic retarder（HARC）And traction control system（TCS）Integrated into an integrated brake control system，For optimum efficiency、Performance and reliability。
Fuel efficiency
When driving downhill，The engine can be further decelerated by compression braking。 When decelerating，Engine ECM Do not inject oil to the cylinder，Fuel economy can be further improved。
Structure
Box section design
793D The frame of the is designed with box section.，At high stress location，Two forgings and 24 castings combined，By deep penetration and continuous wrap-around welding，No need to add weight，It is sufficient to counteract the damage that can be caused by twisting loads.。
Integral four-column ROPS Cab
The integral ROPS is designed as an extension of the truck frame，Resiliently mounted to the main frame，Vibration and noise can be reduced。 ROPS/FOPS The structure provides the operator with“Five-sided protection”。
Suspension system
Designed to dissipate the impact of haulage and loading，Extend the life of the rack，Make driving more comfortable。
Monitoring System
VIMS™ Monitoring System
Caterpillar The intelligent machine monitoring system is designed to provide important machine condition and payload data in real time.，Guarantee 793D Performance is always at a high productivity level。
Integrated system monitoring
Sensors throughout the various systems of the machine VIMS The system is able to quickly exchange and monitor information from all machine systems，Thereby being efficient、Operate with high performance。
Advanced Diagnostics
VIMS The system can find anomalies before they cause serious damage，This simplifies troubleshooting、Reduce downtime and lower operating costs。
Data access
Monitoring and diagnostic information before it is downloaded for analysis，Stored on the truck。 Data can be accessed through the Information Center，Transmission with optional radio，Or download to a computer for detailed analysis。
Machine management
Maintenance technicians or mine personnel can download data and generate reports，To better manage the machine。 The data can be used to improve the effectiveness of the scheduled maintenance program、Maximize component life、Improve machine availability and reduce operating costs。
Speedometer/Tachometer module
Monitor 3 systems：Engine speed、Ground speed and gear indicator。
Instrument cluster
The instrument cluster is positioned for easy viewing，Continuous display of critical machine function information，Include：
Engine coolant temperature
Brake oil
Air system pressure
Fuel level
Keyboard
Allows the operator or service technician to view the current machine information directly through the display on the message center、Meter values and stored data。
Information Center
Displays information required by the operator，The operator is alerted to the abnormal condition of the machine。
Alarm system
Class III warning system alerts the operator：Abnormal machine conditions exist。
Production management
Production Management can Improve Trucks/Efficiency of loading tool、Improve the production capacity of the fleet，Helps extend truck frame、Tire、Service life of rims and driveline component，While reducing operational and maintenance costs。
VIMS PC
External Reporting Software Program VIMS-PC Allows service personnel to download complete machine health records and job efficiency data to a laptop，For diagnosis and analysis。 This easy-to-use software allows service technicians and mine personnel to generate health and payload reports，In order to manage machines more efficiently。
VIMS Supervisor
This optional software allows mine personnel to easily manage and interpret VIMS Data，To optimize fleet management and productivity。
Truck body system
Cat Truck body
Caterpillar Available in 3 specialized body styles and custom body option，Provide customers with the lowest cost per ton transportation solution。
Double oblique
Ping
Design specific to mining（MSD II）
Body selection
The selection of the appropriate body depends on the material being transported and the road conditions.。 The more practical the body is,，The higher the efficiency。 Yours Cat Dealers can be specific to the job site，Help you choose the right body system。
Hopper/Chassis integration
Caterpillar Designed truck body for use with integrated undercarriage，The structure is reliable、Durable，Long life。
Electronic Hoist Control System
When uninstalling，Operator has better control of the load，Load control including yaw，And adjust the control throughout the operation。 The body automatic cushioning feature lowers the pressure on the frame.、Lift Cylinder and Operator Shock。
Short lifting cycle times
Two-stage lift cylinders for quick unloading，20 for lifting and 20 for lowering.25 seconds and 17.5 seconds。
Body liner
There are many different bushings to choose from，To reduce weight、Extend the life of the body system。 Wear-resistant bucket face and bushings to handle intense load impact，At the same time, it is wear-resistant。 Wear plates provide long life in areas of high wear。 Modular bushing plate assembly：
Smooth
Stone
Zipper net
Mechanically attached wear plate system（MAWPS）
Customize the body solution
Tail extension available、Side panel、Anti-slip strip、Stone bin and rock pusher，To achieve the rated payload，Reduce spillage and improve transport efficiency。
The side panels are designed to support the total machine weight to the greatest extent possible
The tail extension is used to help carry the material pile at the rear of the vehicle.，Prevention of spillage of loaded material on the haul road，So that that service life of the tire is prolon。
Target Payload Policy
Yours Caterpillar Dealers can help you manage the target payload，To optimize equipment usage、Ensure safe operation、Increase productivity and reduce cost per ton。
Underloading increases costs by not reaching the payload，So that the equipment cannot be fully utilized，Thereby increasing the cost per ton
Overloading or exceeding the maximum gross machine weight can cause damage to vehicle components,（Uch as a brake、Tires and Power Train）Excessive wear and tear，This in turn reduces component life and increases maintenance and repair costs。
Body design
Cat Truck body design for high strength、Large capacity，And is durable。 The wear-resistant bucket surface is used to overcome severe impact and wear on long-distance transportation.，Without impairing the load capacity
Five side plate reinforcing beams are welded at the joint of the side wall and the bottom plate，Provides increased body stiffness and strength
Wide reinforcing ribs on the floor of the body provide durability and impact resistance
Full length longitudinal stiffeners improve the overall strength and stiffness of the bottom panel
Box-section beams raise the floor、Side panel、Top guard rail、Durability of corners and cabs。
1）Dual ramp body
The dual ramp body is designed with V Type soleplate，Load capacity can be improved、Keep your center of gravity low、Reduce the impact load，And maintain optimal load distribution on steep grades and severe haul road condition。
Top rail made of reinforced rolled steel for increased body strength，It also protects the body from damage from loading tools or falling material
With an inclination of 8 degrees“V”Type a construction to reduce impact loads，And center the load
7.5 degree body tilt forward and 16 degree body tilt backward，Good for holding load on steep slopes。
2）Flat bottom body
Slightly angled, flat-bottomed construction provides excellent payload capacity，And that unload space is large.、Uninstall went smoothly、Easy to control。
Flat-bottom design also keeps the rear of the car worn evenly
Body Tilt 12 degrees forward，Good load capacity on well maintained haul roads
Steel surface hardness of 400 degrees Brinell provides superior wear resistance。
3）Design specific to mining（MSD II）Hopper
Light MSD II The body is based on a flat floor design and is customized for the customer，Maximize payload potential and reduce cost per ton。 Design each MSD II First of all, the hopper should be combined with the complex landform of the mine site.，Then refer to the specific mining requirements.，Carry out development。
Customer support
Promise to make Caterpillar Remarkable
By offering multiple solutions、Services and products，Cat Dealers can help you reduce cost、Increase productivity、Manage your business more effectively。 Support goes well beyond parts and repair。 Select from Cat Equipment until refurbishment、Trade or sell，Cat Dealers are able to provide differentiated service and support to their customers。
Agent capability
Cat Agents provide a wide range of services to customers worldwide。 The dealer's technical specialist has the requisite knowledge、Experience、Training skills and tools，Your repair and maintenance needs can be met anytime, anywhere。
Product support
Cat The agent firmly believes，Quality products should be supported by quality services.。 Cat After the product is put into use on site，Will get the parts distribution agency.、Supported by a global network of dealer service centers and technical training facilities，This ensures that your equipment is functioning properly。 Our global dealer network delivers timely、Reliable parts supply and expertise，Ready to meet your needs 24/7，Cat Customers can count on us。
Service support
Cat The equipment is designed and manufactured to provide maximum productivity and most economical operation throughout its life。 Cat Agents offer a variety of service plans，Maximize machine uptime and your return on investment，These services include：
Preventive maintenance plan
Troubleshooting plan，Uch as scheduled oil sampling and TES.
Refurbishment and remanufacturing option
Customer Service Agreement
Understand the application
Operating and maintenance costs are influenced by many application and site-specific factors，Uch as material density、Loading position、Payload、Slope、Speed、Haul road design and maintenance。 To optimize TCO and productivity，Cat Your dealer can provide you with the appropriate information，Gives you an overview of the impact of specific uses and operating techniques on maintenance and operating costs。
Operation
Nowadays, products are more and more complex.，The equipment controller must have a thorough knowledge of the machine systems and operating techniques.，Only in this way can we achieve the highest efficiency and maximum benefits.。 Cat Dealers can schedule training programs to help operators increase productivity、Reduce downtime、Reduce operating costs、Enhance security and improve your Cat Return on investment of the product。
Technical products
Cat Agents can provide a variety of advanced technology products.，Such as VIMS® Monitoring system and MineStar® Information Management System。 These products include radio data communications.、Machine monitoring and diagnostics、Fleet management and transportation road maintenance software，All products to improve fleet efficiency、Designed to increase productivity and reduce costs。
Console
Ergonomic layout
793D The operator station is ergonomically designed，Allows the operator to be in a comfortable、Operate all machine controls in a productive and safe environment。 All controls、Joystick、Reasonable layout of switches and instruments，Maximize productivity and reduce operator fatigue。
Quiet cab
Integral type ROPS/FOPS The noise suppression cab is resiliently mounted to the main frame，Isolate the operator from the source and the sources，So that that drive is quiet、Safe and comfortable。
View
The wide field of vision gives a panoramic view of the surroundings，Clear line of sight on the road，Allows the operator to operate with confidence，Increase productivity。
1）Air Suspension Seat, Operator, Three-Point Mount
The air suspension seat is ergonomically designed，Its armrest can be adjusted in all directions.，To achieve the best driving comfort。 Telescopic wide seat with three-point fastening/Safety belts provide operator safety、Comfortable protection。
2）Lift lever
The electronic lift control system with push-button control has 4 positions to choose from，And that operation is labor-saving，It is mounted next to the operator's seat，And is convenient to operate。
3）Secondary brake pedal
Located on the floor in an easily accessible position，And is convenient to control by an operator。
4）Monitoring System
VIMS The system is equipped with an easy to read display and operator friendly input keypad，Provide accurate machine status information。
5）Steering column
Comfortable steering wheel with tilt and telescope provides a comfortable driving position。
6）Transmission console
Ergonomic shifter with black backlit indicator，And that efficiency is improve。
7）Parking brake reset valve
When the air system is bled，The parking brake cannot be released until the valve button is reset。
8）Storage Room
Located under the trainer seat，Safe and clean。
9）Trainer seat
Full size、Fully padded trainer seat，Has a backrest，Large hip and shoulder room，With seat belt，Driving safety。 Optional air suspension seat。
10）Operator window
Power Operator Window and Sliding Trainer Seat Window，The operation is simple，Wide field of vision。
11）Operator controls
Closely placed turn signal、High beam、Intermittent windscreen wiper and windscreen washer control，Have high efficiency、Comfortable design。
12）Heating/Air conditioner
Temperature-controlled air circulation via an electronically controlled four-speed fan and 11 vents，Provides a comfortable working environment in all weathers。 More robust air compressor provides greater durability and longer service life。
Reserved for communication system
The cab is a power converter、Speaker、Wiring harness and antenna are pre-routed，And for the radio device to be added、CCTV and MineStar® The installation position is reserved for the system。
Serviceability
Maintenance is simple
Convenient maintenance of daily maintenance points, simplified maintenance，And reduce that time required for routine maintenance procedure。 Increased serviceability and up to 500-hour service intervals increase machine availability and productivity。
Maintenance platform
Provide for the engine、Air Cleaner、Steering Hydraulic Tank and Battery Box Overhaul。
Overhaul in the frame
Allow easy access to major components，Convenient for maintenance and disassembly。
Ground maintenance
And that box body is convenient to maintain、Filter、Drain and engine shutdown device。 Located on the ground VIMS Data port for easy downloading of information。
Automatic lubrication
The automatic lubrication system automatically lubricates critical components at regular intervals.，This reduces maintenance times。
Fast Fill Service Center
Optional Wiggins Fast fill service center for quick fuel and oil changes。
Refueling system（ORS）
The optional on-board engine oil management system is designed to increase oil change times，Reduce oil handling efforts and costs to increase machine availability and productivity。 ORS For measuring the oil level and filling the fuel return line of the engine with used engine oil from the crankcase。 The new oil needs to be added manually during routine maintenance.。
Scheduled oil sample analysis
S•O•SSM Sampling valve reduces time for sampling and reliability analysis。
Pressure test point
Block valves are conveniently located throughout the hydraulic system，It is convenient to test the pressure。
Air Cleaner
Radial seal air filters are easy to replace，Less maintenance time required。
Sealed electrical receptacle
Electrical connectors are sealed，Protects against dust and moisture。 The harness is braided in a staggered manner，Provides excellent protection。 Wires are color-coded，Easy to diagnose and repair。
Cylinder head
All cylinder heads are interchangeable，To facilitate disassembly and visual inspection of internal part。
On-board diagnostic system
VIMS The system continuously checks all critical functions and components of the machine，Assist in quick troubleshooting and quick repair。 With the help of an electronic technician（Cat ET）Service tools，The electronic control system can quickly diagnose the engine condition，And carry out effective maintenance and repair。
Rearview mirror
The left mirror mounting bracket is more robust，And that len can be easily replaced.，Without the need to replace the mirror assembly with a new one.。 The new mirror lens can be slid in and out of the bracket，Reduced downtime and repair cost。
Security
Product safety
Caterpillar We will continue to proactively develop mining machines that meet or exceed safety standards.。 Safety is an integral part of all machine and system design。
SAE And ISO Standard
793D Designed to meet multiple national and international standards。
Integral type ROPS Cab
The integral ROPS is designed as an extension of the truck frame，Resiliently mounted to the main frame，Vibration and noise can be reduced。 ROPS/FOPS The structure provides the operator with“Five-sided protection”。
Ladder/Auxiliary exit
Fixed spacious staircase for easy access to the machine。 The ladder on the left side of the machine is an auxiliary access or emergency exit。
Braking system
The oil-cooled brake system distributed at the four corners of the body provides excellent control of the machine in case of slippage.。 The service brakes and the retarding system are activated by adjustable hydraulic pressure，The secondary brake and parking brake functions are spring actuated、Hydraulic release。 This system ensures braking in the event of a complete hydraulic failure。
Steering system
Steering system construction with double-acting dual cylinders provides precise control in all loading and ground conditions。 The steering hydraulic system is separated from the main hydraulic system.，Avoid cross-contamination and overheating from other sources。
Engine shutdown switch
One secondary engine shutdown switch is located at ground level。
Open circuit in the electrical system
The battery disconnect switch is located directly above the front bumper，The electrical system can be locked from the ground。
Overload policy
In the operation of mining equipment，Safety is an integral part of maintaining maximum operational efficiency。 Caterpillar 10 of/10/The 20 overload policy ensures that the steering and braking systems have sufficient performance，Even at overload 20% The situation is no exception.。
Standard safety features
Non-slip watch
75 mm（3"）Wide orange three-point fixed operator safety
Wide Angle
Body raise indication
Body retaining cable
Shield guide
Reverse Neutral for Dump
Low internal noise level
Product Parameter
Engine |
|
| Engine model | Cat 3516B HD EUI |
| Total power - SAE J1995 | 1801.0 kW |
| Rated power | 1801.0 kW |
| Net power - ISO 9249 | 1743.0 kW |
| Net power - 80/1269/EEC | 1743.0 kW |
| Torque reserve | 23.0 % |
| Cylinder bore | 170.0 mm |
| Stroke | 215.0 mm |
| Displacement | 78.0 l |
| Net power | 1743.0 kW |
| Net power - SAE J1349 | 1743.0 kW |
Weight - Approximation |
|
| Total operating weight of the machine（GMW） | 383749.0 kg |
| Chassis weight | 116707.0 kg |
| Body weight range | 21795 - 54431 kg / 48050 - 120000 lb |
Operating specifications |
|
| Nominal payload capacity | 218.0 ton (US) |
| Body capacity（SAE 2:1） | 129.0 m³ |
| Top speed - Fully loaded | 54.3 km/h |
| Maximum payload capacity | 218.0 ton (US) |
| Maximum payload capacity | Customize |
| Steering angle | 36.0 degrees |
| Lifting time | 20.3 seconds |
| Descent time | 17.5 seconds |
| Circle clearance diameter | 32.66 m |
| Turning diameter - Front | 28.42 m |
Final drive |
|
| Differential gear ratio | 1:8:1 |
| Planetary gear ratio | 16:1 |
| Total reduction ratio | 28.8:1 |
Gearbox |
|
| First gear forward | 11.8 km/h |
| Second gear forward | 15.9 km/h |
| Third gear forward | 21.5 km/h |
| Fourth gear forward | 29.0 km/h |
| Fifth gear forward | 39.4 km/h |
| Sixth gear forward | 54.3 km/h |
| Go backwards | 10.9 km/h |
Suspension system |
|
| Effective cylinder stroke – Front | 130.5 mm |
| Effective cylinder stroke – Rear | 105.5 mm |
| The rear axle swings | +/- 4.9º |
Body lift system |
|
| Pump flow - High idle | 846.0 l/min |
| Relief valve setting - Rise | 20370.0 kPa |
| Body raise time - High idle | 20.25 seconds |
| Body down time - Float | 19.26 seconds |
| Body power is reduced - High idle | 17.51 seconds |
Brake |
|
| Outside diameter | 874.5 mm |
| Braking area - Rear brake | 134500.0 cm² |
| Standard | J-ISO 3450 JAN88、ISO 3450:1996 |
| Braking area - Front brake | 89817.0 cm² |
Weight distribution - Approximation |
|
| Front axle - Fully loaded | 33.0 % |
| Rear axle - Fully loaded | 67.0 % |
| Front axle - No load | 46.0 % |
| Rear axle - No load | 54.0 % |
Capacity - Double Bevel - 100% Fill factor |
|
| Stacking（SAE 2:1） | 129.0 m³ |
| Paperback | 96.0 m³ |
Maintenance refill capacity |
|
| Fuel tank（Standard） | 4354.0 l |
| Fuel tank（Optional） | 4922.0 l |
| Cooling system | 973.0 l |
| Crankcase | 265.0 l |
| Rear axle housing | 1022.0 l |
| Steering tank | 227.0 l |
| Steering system（Including the fuel tank） | 341.0 l |
| Braking/Raise the hydraulic tank | 769.0 l |
| Braking/Lifting system（Including the fuel tank） | 1375.0 l |
| Torque converter/Transmission oil sump | 102.0 l |
| Torque converter/Transmission system（Includes an oil sump） | 189.0 l |
Tire |
|
| Standard Tyre | 40.00R57 |
Size |
|
| Front headliner height | 6494.0 mm |
| To ROPS The height of the top | 5584.0 mm |
| Overall body length | 12862.0 mm |
| Inside body length | 7712.0 mm |
| Total length | 12862.0 mm |
| Wheelbase | 5905.0 mm |
| Distance between rear axle and tail | 3772.0 mm |
| Ground clearance | 1005.0 mm |
| Unloading clearance | 1364.0 mm |
| Loading height - No load | 5871.0 mm |
| Maximum Inside Body Depth | 2330.0 mm |
| Overall height with body raised | 13113.0 mm |
| Working width | 7680.0 mm |
| Width between center lines of front tire | 5610.0 mm |
| Engine guard clearance | 1294.0 mm |
| Overall width of headliner | 7680.0 mm |
| Outside width of body | 7680.0 mm |
| Inside body width | 6500.0 mm |
| Rear axle clearance | 1128.0 mm |
| Width between center lines of rear dual tire | 4963.0 mm |
| Overall tire width | 7605.0 mm |
ROPS |
|
| ROPS Standard | .ISO 3471:1994 |
Noise |
|
| Noise standard | .ANSI/SAE J1166 MAY90 |
Turn |
|
| Steering Standard | SAE J1511 OCT90、ISO 5010:1992 |
